Laundry Room Cabinets, Built Around Your Machines
The laundry room gets treated as an afterthought and then used more than the dining room. It is also the most technically annoying room in the house to cabinet: there is a water supply, a drain, a dryer vent, a gas line or a 240-volt outlet, and two large appliances that vibrate.
Cabinets built for that room work around all of it. Cabinets bought by the box get cut on site with a jigsaw and never quite close right.
We Map the Utilities Before Anything Gets Built
At the measure we locate every supply valve, drain, vent and outlet, and we design the cabinet run around them.
Where a cabinet back has to pass over a shutoff or a cleanout, we cut a precision access port into the shop drawing rather than hacking a hole on install day. The point is that in eight years, when a supply line drips, the plumber can reach the valve without pulling your cabinetry off the wall.
Clearances around the machines get respected. A washer that is packed in tight walks into its neighbors on every spin cycle, and vibration against a cabinet side panel is how you get a rattle you cannot find and a finish that wears through from the inside.
Ask a Question
Laundry Cabinets Hold More Weight Than You Think
A shelf of detergent, softener, bleach and a full basket runs 60 to 70 pounds. That is heavier than almost anything in a kitchen upper.
We anchor with high-shear fasteners driven into wall studs, not into drywall and not into a cleat that is only catching plaster. Tall cabinets and floor-to-ceiling storage towers get a full-height anchor so a loaded unit cannot tip.
The shelving gets sized for the load too. A 36-inch span of thin shelf with a case of detergent on it sags, and a sagging shelf never un-sags.
What Actually Makes a Laundry Room Work
- A folding counter. The single best thing you can add. A waterfall countertop that runs over the top of front-loading machines turns two appliances into a work surface. If your machines are top-loading, the counter goes beside them instead, and we size the run so a basket fits underneath.
- Pull-out drying racks. Built into a base cabinet, calibrated for tension so they extend smoothly and hold flat when loaded.
- Valet rods. A short hanging rod, either concealed under an upper or pulled out from a cabinet side, for anything coming straight out of the dryer.
- A tall broom and vacuum cabinet. Full height, one door, no shelves in the bottom two-thirds. Nobody regrets this one.
- A drop zone, if the laundry is also the way into the house from the garage. Hooks, a bench, cubbies and shoe storage, built in the same species and finish as the rest of the run.
- Vertical storage. Most laundry rooms are small and have more wall than floor. Tall and narrow beats wide and shallow in a room where you are standing in front of an open machine door.
Sealing, Because Humidity Is the Failure Point
Every cut edge gets sealed before the cabinet leaves our shop, where our Amish cabinetmakers build and finish each run to order. A laundry room runs warmer and wetter than the rest of the house, and an exposed edge is where swelling and peeling start — it is the most common failure we see when we are called in to replace somebody else's work.
Finish coats are the same catalyzed topcoat we use in kitchens and baths. Detergent and bleach splash gets wiped off rather than soaking in.
Basement Laundry, Second-Floor Laundry, Closet Laundry
Basement. Concrete floor, often damp, often out of level by more than you would guess. We raise base cabinets clear of the slab rather than setting wood on concrete, and we laser-level the run instead of trusting the floor.
Second floor. Usually tight, usually a closet or a converted hall alcove. The whole job is getting real storage into a footprint that is maybe five feet wide, with a pan under the machines and a stacked unit. Bifold or pocket doors matter here because a swinging door eats the room.
Main-floor closet. The design problem is doors that hide the machines when closed and clear them completely when open. That usually means bifolds or full-overlay doors sized to the opening, not a pair of standard cabinet doors.
Laundry Room Cabinets in Your Town
We build and install across Chester County and Delaware County. Find your town:
- Berwyn, PA
- Chadds Ford, PA
- Chester County, PA
- Chester Springs, PA
- Chesterbrook, PA
- Coatesville, PA
- Delaware County, PA
- Downingtown, PA
- Elverson, PA
- Exton, PA
- Frazer, PA
- Glen Mills, PA
- Honey Brook, PA
- Malvern, PA
- Morgantown, PA
- Newtown Square, PA
- Paoli, PA
- Parkesburg, PA
- Unionville, PA
- Wayne, PA
- West Chester, PA
Frequently Asked Questions
-
Can you build around my existing washer and dryer?
Yes. Bring us the make and model, or we will measure them at the consultation. If you are planning to replace the machines within a few years, tell us — we will design to the larger footprint so a future upgrade does not mean new cabinets. -
Will a counter over my front-loaders block the detergent drawer?
Not if it is measured right. We set the counter height off the machines' actual dimensions with clearance for the lid or drawer to open fully, plus room for the vibration pad. -
Is a laundry room worth doing in solid wood?
It is the room where cheap cabinetry fails fastest, so yes. Humidity, detergent and weight are exactly the conditions that expose particleboard and thin veneer. -
Can you match the laundry cabinets to my kitchen?
Yes, if the kitchen cabinetry is something we can see and sample. Matching an existing finish from another maker is harder than matching our own, and we will be honest about how close we can get. -
How long does a laundry room take?
Shorter than a kitchen from an install standpoint, but from the time you reach out to a finished project, most laundry room cabinets run 2 to 6 months, depending on size, finish and how it lines up with any surrounding renovation. -
Do you move the plumbing or the dryer vent?
No, but we coordinate it. If the design calls for relocating a hookup, we bring in a plumber or electrician we have worked with for years and run the schedule so the rough-in happens before the cabinets arrive.
Get Started
Call 717-692-1200 or request an estimate. 353 Pequea Ave, Honey Brook, PA 19344 · Monday–Friday, 8:00 AM–5:00 PM
Start Your Project Today